To calculate your home heating cost, multiply the energy your heating system uses by your price per unit of energy: kilowatt-hours for electric heat, cubic metres for natural gas, or litres for oil and propane. To compare systems fairly, convert everything to a cost per kilowatt-hour of useful heat, which accounts for efficiency. This guide gives the formulas, energy conversion factors, a comparison table and worked examples for a Canadian winter.
How to calculate home heating cost: the basic formula
Every heating calculation follows the same logic, whatever the fuel.
Heating cost = energy used × price per unit
The difficulty is knowing how much energy you will use. There are three practical ways to estimate it:
- From past bills: the most accurate method. Look at your winter consumption and subtract the typical summer baseline to isolate heating.
- From the heater’s power: for space heaters and baseboards, multiply wattage by hours of operation.
- From the heat your home needs: estimate the total heat demand for the season, then divide by the efficiency of each system to compare options.
Energy conversion factors you need
To compare fuels, convert each one to kilowatt-hours (kWh) of energy. The values below are typical approximate energy contents used in Canadian energy calculations.
| Energy source | Unit | Approximate energy content | Typical system efficiency |
|---|---|---|---|
| Electricity (baseboard, space heater) | 1 kWh | 1 kWh | 100% |
| Electricity (air-source heat pump) | 1 kWh | 1 kWh in, 2 to 3 kWh of heat out | Seasonal COP of about 2 to 3 |
| Natural gas | 1 m³ | About 10.4 kWh | 90% to 97% (high-efficiency furnace) |
| Heating oil | 1 litre | About 10.7 kWh | 80% to 87% |
| Propane | 1 litre | About 7.0 kWh | 90% to 95% |
Heat pump performance drops in very cold weather, so its seasonal efficiency depends heavily on your climate and on whether you keep a backup system for the coldest days. Use our unit converter if you need to switch between gigajoules, BTU and kWh.
Cost per kWh of useful heat
The fairest comparison is the price you pay for each kWh of heat that actually reaches your rooms:
Cost per useful kWh = price per unit ÷ (energy per unit × efficiency)
| System | Example price (illustrative) | Cost per useful kWh |
|---|---|---|
| Electric baseboard | $0.10 per kWh | $0.100 |
| Heat pump (COP 2.5) | $0.10 per kWh | $0.040 |
| Natural gas furnace (95%) | $0.45 per m³ all-in | About $0.046 |
| Oil furnace (85%) | $1.60 per litre | About $0.176 |
| Propane furnace (92%) | $0.90 per litre | About $0.140 |
The prices above are examples only, not current rates. Electricity and fuel prices vary a lot between provinces and suppliers, and gas bills include delivery and fixed charges, so plug in the all-in price from your own bill.
Worked example: space heater in a basement office
A 1,500 W space heater runs 6 hours a day for 120 days of winter, with electricity at $0.10 per kWh.
- Energy per day: 1,500 W × 6 h ÷ 1,000 = 9 kWh.
- Energy per season: 9 kWh × 120 days = 1,080 kWh.
- Cost: 1,080 kWh × $0.10 = $108 for the winter, or about $0.90 per day.
The same method works for any electric appliance; see our guide on calculating the electricity cost of an appliance.
Worked example: comparing systems for a whole house
Suppose a house needs about 20,000 kWh of useful heat over the season, a common order of magnitude for a detached home in a cold Canadian climate (your actual need could be much lower or higher).
- Electric baseboards: 20,000 kWh × $0.100 = about $2,000.
- Heat pump with COP 2.5: 20,000 kWh × $0.040 = about $800, plus backup heat on the coldest days.
- Natural gas furnace at 95%: 20,000 kWh × $0.046 = about $920, plus monthly fixed charges.
- Oil furnace at 85%: 20,000 kWh × $0.176 = about $3,520.
This kind of comparison is the starting point for deciding whether a heat pump or a furnace upgrade pays for itself. Divide the installation cost by the annual savings to get a simple payback period in years.
Estimating heat demand from your home’s size
If you have no past bills, a rough estimate uses floor area and an energy intensity figure. Measure your heated area with our square footage calculator, then multiply by a heating intensity in kWh per square metre per year. Older, poorly insulated homes can use two to three times more heat per square metre than new, airtight ones. Because these figures vary so widely, use them only for rough planning and rely on an energy audit for big decisions.
Using your bills to isolate heating costs
Past bills are the most reliable data you have. A simple method works for both electricity and gas.
- Collect 12 months of bills, ideally from your utility’s online account where consumption is shown by month.
- Find your baseline: the average monthly consumption in months with no heating, typically June to September.
- For each heating month, subtract the baseline from that month’s consumption. What remains is mostly heating.
- Add those heating portions for the whole season.
- Multiply by your all-in variable rate to get the seasonal heating cost.
For example, if your home uses 700 kWh in a typical summer month and 2,400 kWh in January, roughly 1,700 kWh of January’s use is heating. At $0.10 per kWh, that is about $170 of heat for the month. Repeat for each winter month and you have a realistic seasonal figure to compare with the cost of an upgrade.
Thermostat setbacks: estimating the saving
Lowering the temperature reduces the difference between indoor and outdoor air, which reduces heat loss. Natural Resources Canada suggests that lowering the thermostat at night and when the house is empty can noticeably reduce heating costs, with the saving depending on climate and how long the setback lasts. To estimate your own result, compare a few weeks of consumption before and after you change the schedule, adjusting for outdoor temperature.
Electric heat and time-of-use rates
Some provinces offer time-of-use or dynamic electricity rates. Preheating a well-insulated home during cheaper hours can lower costs, but only if your rate plan and heating system allow it. Read your utility’s rate schedule before relying on this strategy.
Checklist to lower your heating bill
- Lower the thermostat at night and when nobody is home; each degree of setback reduces heat loss.
- Seal drafts around windows, doors and baseboards before the cold arrives.
- Replace or clean furnace filters every one to three months during the heating season.
- Add attic insulation, often the most cost-effective upgrade.
- Check your utility’s time-of-use or dual-energy rates if available in your province.
- Look up federal and provincial rebate programs for heat pumps and insulation before buying.
FAQ
How do I convert my gas bill from gigajoules to kWh?
One gigajoule equals about 277.8 kWh. Some utilities bill in GJ and others in m³; one cubic metre of natural gas contains roughly 0.0373 GJ.
Is a space heater cheaper than central heating?
Only if you heat a single room and lower the thermostat elsewhere. Per unit of heat, a space heater costs the same as electric baseboards and more than a heat pump or efficient gas furnace.
Why is my bill higher than my calculation?
Bills include fixed monthly fees, delivery charges, taxes and non-heating uses such as hot water and cooking. Colder-than-average months also increase demand.
What does COP mean for a heat pump?
The coefficient of performance is the heat delivered divided by the electricity used. A COP of 3 means 3 kWh of heat for every 1 kWh of electricity.
In short: convert every fuel to a cost per useful kWh, multiply by your home’s heat demand, and you can compare systems in minutes. Prices in this article are illustrative; use the all-in rates on your own bills for an accurate estimate, and consult a certified energy advisor before major upgrades.