For an L-shaped room, split it into rectangles, run each one, and add the results. Subtract large areas such as a tub or cabinets.
This tile calculator tells you how many tiles and how many boxes to buy for a floor, a backsplash or a shower wall. Enter the size of the surface, the tile size and the grout joint, choose a waste allowance, and it rounds up to full boxes with an estimated cost. It works in imperial (feet and inches, as most Canadian stores label tile) or metric.
How the tile calculation works
- Area = length × width of the surface.
- Area covered by one tile = (tile length + grout joint) × (tile width + grout joint). Each tile "owns" half the joint on every side, so the joint is added once to each dimension. In imperial, the result in square inches is divided by 144 to get square feet.
- Tiles needed = area ÷ area per tile.
- Tiles to buy = tiles needed × (1 + waste % ÷ 100), rounded up.
- Boxes = tiles to buy ÷ tiles per box, rounded up to a whole box.
The grout joint matters more than people think with small tiles. On a 2 × 2 inch mosaic, a 1/8 inch joint adds more than 12% to the area each tile covers, so you need fewer tiles. On large-format tile, the joint has almost no effect.
Worked example
You are tiling a 10 × 12 ft kitchen floor with 12 × 24 inch porcelain tiles and a 1/8 inch (0.125 in) grout joint. The tiles come 8 per box at $45 a box.
- Area: 10 × 12 = 120 sq ft (11.15 m²)
- Area per tile: (12.125 × 24.125) ÷ 144 = 2.031 sq ft
- Tiles without waste: 120 ÷ 2.031 = 59.07, so 60 tiles
- With 10% waste: 59.07 × 1.10 = 64.98, so 65 tiles
- Boxes: 65 ÷ 8 = 8.1, so 9 boxes (72 tiles)
- Cost: 9 × $45 = $405 before tax
The seven spare tiles are not wasted money. Keep them for repairs: tile lots change colour slightly between production runs, and finding an exact match a few years later is hard.
Waste allowance by layout
Waste covers cut pieces you cannot reuse, breakage and the odd tile with a defect. The values below are common rules of thumb used by installers. They are not official standards, so ask your tile supplier or installer for the figure that fits your job.
| Layout or situation | Typical waste allowance |
|---|---|
| Straight lay (grid), simple rectangular room | 10% |
| Offset or brick pattern (1/3 or 1/2 offset) | 10% to 12% |
| Diagonal (45°) layout | 15% |
| Herringbone or chevron | 15% to 20% |
| Small room with many corners, toilet, pipes or niches | 15% or more |
| Natural stone or handmade tile with variation | 15% to 20% |
Common tile sizes and coverage
| Nominal tile size | Coverage per tile (no joint) | Tiles per 100 sq ft (no joint, no waste) |
|---|---|---|
| 12 × 12 in (30 × 30 cm) | 1.00 sq ft | 100 |
| 12 × 24 in (30 × 60 cm) | 2.00 sq ft | 50 |
| 18 × 18 in (45 × 45 cm) | 2.25 sq ft | 45 (44.4 rounded up) |
| 24 × 24 in (60 × 60 cm) | 4.00 sq ft | 25 |
| 3 × 6 in subway tile | 0.125 sq ft | 800 |
Note: metric tiles labelled 30 × 60 cm are slightly smaller than true 12 × 24 inch tiles. Enter the real size printed on the box for the most accurate count.
Measuring tips
- Measure each wall or floor at its longest and widest point, to the nearest inch or centimetre. Our square footage calculator helps with several rooms or odd shapes.
- For walls, measure only the part you will tile, such as the backsplash height between the counter and the upper cabinets.
- Subtract large openings like doors and windows, but do not subtract small items like outlets.
- Check the box for coverage. Many manufacturers print the square feet per box, which is a good cross-check on the calculator.
Common mistakes
- Buying the exact number of tiles. Without waste, you will run short at the last row of cuts.
- Mixing units. Room size in feet and tile size in inches is correct for the imperial setting. Do not type a tile size in feet.
- Buying from different lots. Make sure every box carries the same lot or batch number to avoid colour shifts.
- Forgetting the trim. Bullnose, edge profiles and transition strips are sold separately and are not counted here.
- Skipping the setting materials. Thin-set mortar, grout and spacers are extra. Budget for them along with the tile. If you are pouring a base slab first, see our concrete calculator.
FAQ
How many tiles do I need for 100 square feet?
With 12 × 24 inch tiles and a 1/8 inch joint, about 50 tiles cover 100 sq ft, or 55 tiles with 10% waste. Smaller tiles need many more: about 100 tiles of 12 × 12 inches before waste.
How much extra tile should I buy?
Plan for 10% on a straight layout and 15% to 20% for diagonal, herringbone or a room with many cuts. Most stores accept returns of unopened boxes, but check the policy before you buy.
Does grout size change the number of tiles?
Yes, slightly. A wider joint means each tile covers more area, so you need fewer tiles. The effect is small for large tiles and noticeable for mosaics.
How do I convert square metres to square feet?
Multiply square metres by 10.764. A 10 m² floor is about 107.6 sq ft. The calculator shows both units, and our unit converter covers other conversions.
Can I use this for wall tile in a shower?
Yes. Run each wall as its own rectangle and add the totals. Use at least 15% waste because showers have niches, valve cut-outs and many edge cuts.
Disclaimer: this tile calculator gives an estimate only, not professional or financial advice. Confirm quantities with your supplier or installer before you order, especially for patterned layouts.
Related: Square Footage Calculator · How to Calculate the Square Footage of a Room · Room Paint Calculator · Concrete Calculator
You can also compare your result with this flooring cost calculator.